How To Remove Mixer Grinder Motor Coupler

If your mixer grinder motor coupler is preventing your machine from operating, there are a few quick and easy steps you can take to remedy the problem.

How to remove mixer grinder motor coupler

If you’re looking for a way to remove the mixer grinder motor coupler on your KitchenAid blender, you’re in luck. This job can be done relatively easily using a few simple tools and some common sense.

First, you’ll need to remove the cover of the blender motor. This can be done by removing the four screws that hold it in place, or by prying it off with a flathead screwdriver. Once the cover is removed, you’ll be able to see the mixer grinder motor inside.

Next, you’ll need to unscrew the mixer grinder motor coupler. This is a small, round screw located on the side of the blender motor. It’s generally easy to access, and can be unscrewed with a Phillips head screwdriver. Once it’s unscrewed, you can remove it from the blender motor.

Also Check   How To Fix Juicer Mixer Grinder

Steps to remove mixer grinder motor coupler

1.Remove the grinder motor coupling

2.Remove the screws that hold the grinder motor in place

3.Carefully pry the grinder motor out of the coupling

4.Once the grinder motor is free, be sure to clean all the dust and debris off of it before reinstalling it onto the mixer

5.Reinstall the screws that held the grinder motor in place and you’re ready to go!

Tools needed to remove mixer grinder motor coupler

  • Phillips screwdriver
  • Allen key
  • Cordless drill
  • 1/4 inch drill bit
  • Jigsaw
  • Stiff wire brush
  • New motor
  • New coupler

    1. Locate the mixer grinder motor coupler. It is typically located on the bottom of the mixer grinder.

    2. Remove the Phillips screwdriver from the screwdriver set.

    3. Remove the Allen key from the tool set.

    4. Turn the mixer grinder upside down.

    5. Remove the screw on the bottom of the mixer grinder motor coupler.

    6. Remove the motor from the mixer grinder.

    7. Remove the coupler from the motor.

    8. Clean the motor and coupler with a stiff wire brush.

    9. Replace the motor and coupler in the mixer grinder.

    10. Replace the screw on the bottom of the mixer grinder motor coupler.

Also Check   Can We Carry Mixer Grinder In International Flight

Caution while removing mixer grinder motor coupler

Be very careful while removing the mixer grinder motor coupler. You can easily damage the spindle if not done correctly.

1. Remove the screw that holds the motor coupler in place.

  1. Use a flat head screwdriver to pry the coupler off of the spindle.
  2. Be careful not to damage the spindle in the process.

How to replace mixer grinder motor coupler

If you’ve just noticed that your mixer grinder motor is not working as well as it used to, there’s a good chance that the motor coupler is missing. This small, round metal device connects the motor to the shaft that spins the blades, and if it’s not working properly, the mixer won’t be able to mix ingredients properly. Replacing the motor coupler is a relatively easy job, and can be done in just a few minutes with the right tools. Here’s how to do it:

1. Locate the mixer grinder motor. This might be located on the bottom or side of the machine, and will likely have a number or letter on it.

Also Check   How To Use Panasonic Juicer Mixer Grinder

2. Remove the cover or lid of the machine. This will likely require a screwdriver or a wrench.

3. Locate the mixer grinder motor coupler. It will likely be either attached to the motor or the shaft that spins the blades.

4. Remove the coupler by unscrewing it. Be careful not to lose it – you’ll need it later.

5. Replace the coupler with a new one. Be sure to screw it in place properly.

6. Replace the cover or lid of the machine.

7. Test the mixer grinder motor by turning it on.

Conclusion

The mixer grinder motor coupler is a small and easily removable part that is used to connect the motor to the gearbox of the mixer grinder. If this part is not properly attached or if it becomes worn, the mixer grinder may not operate properly. In order to remove the mixer grinder motor coupler, first remove the screws that hold it in place. Then, use a Phillips screwdriver to unscrew the coupler. Be careful not to loose the screws that hold the coupler in place. Once the coupler is unscrewed, it can be removed and replaced if necessary.